MikroTik RouterOS 6.35.x (Stable)
(перенаправлено с «Изменения в RouterOS:Release 6.35.x»)
Подробное описание изменений в MikroTik RouterOS 6.35.x (Stable). Официальный список исправленных ошибок, добавленного функционала и прочих доработок. Дата выхода первого набора изменений – 14 апреля 2016, дата выхода последнего набора изменений – 9 июня 2016.
Полезные материалы по MikroTik
Углубленный курс "Администрирование сетевых устройств MikroTik" Онлайн-курс по MikroTik с дипломом государственного образца РФ. Много лабораторных работ с проверкой официальным тренером MikroTik. С нуля и до уровня MTCNA.
На Telegram-канале Mikrotik сэнсей можно получить доступ к закрытой информации от официального тренера MikroTik. Подписывайтесь
MikroTik RouterOS 6.35.4
Дата выхода: 9 июня 2016
Изменения:
- address-list - make "dynamic=yes" as read-only option;
- bonding - fixed 802.3ad load balancing mode over tunnels ;
- bonding - fixed bonding primary slave assignment for ovpn interfaces after startup;
- bonding - fixed crash on RoMON traffic transmit;
- dhcpv6 client - fixed ia lifetime validation when it is set by dhcpv6 client;
- disk - added support for Plextor PX-G128M6e(A) SSD on CCR1072;
- ethernet - fixed memory leak when setting interface without changing configuration;
- firewall - do not show disabled=no in export;
- health - fixed broken factory voltage calibration data for some hAP ac boards;
- health - fixed incorrect voltage after reboot on RB2011UAS;
- ipsec - fixed mode-config export;
- ipsec - fixed route cache overflow when using ipsec with route cache disabled;
- lte - use only creg result codes as network status indications;
- ovpn - enable perfect forwarding secrecy support by default;
- rb3011 - fixed port flapping on ether6-ether10;
- rb3011 - fixed reset button functionality;
- rb3011 - improved performance on high cpu usage.
MikroTik RouterOS 6.35.3
Дата выхода: 1 июня 2016
Релиз только для внутреннего использования компанией MikroTik.
MikroTik RouterOS 6.35.2
Дата выхода: 2 мая 2016
Изменения:
- discovery - fixed identity discovery (introduced in 6.35.1);
- firewall - fixed policy routing configurations (introduced in 6.35rc38);
- log - fixed time zone adjustment (introduced in 6.35.1);
- queue - fixed interface queue type for ovpn tunnels;
- snmp - fixed snmp timeout (introduced in 6.35.1);
- vrrp - fixed missing vrrp interfaces after upgrade (introduced in 6.35.1).
MikroTik RouterOS 6.35.1
Дата выхода: 25 апреля 2016
Изменения:
- bonding - do not corrupt bonding statistics on configuration changes;
- bonding - fixed crash when vlan parent mtu is higher than bonding mtu;
- ethernet - do not allow mtu to be higher than l2mtu and l2mtu to be higher than max-l2mtu (reduce automatically on upgrade if it was wrong before);
- log - fixed reboot log messages;
- lte - do not allow to set multiple modes when it is not supported;
- lte - fixed address acquisition on Huaweii LTE interfaces;
- winbox - show voltage in Health only if there actually is voltage monitor;
- wireless - fixed issue when CAPsMAN could lock CAPs interface.
MikroTik RouterOS 6.35
Дата выхода: 14 апреля 2016
Изменения:
- arp - apply Linux Kernel patch to stop RouterOS from randomly exhibiting misplaced ARPs;
- mipsbe - (excluding RB4xx and CRS series) fixed rare ethernet tx buffer corruption;
- nand - implemented once a week nand refresh to improve stored data integrity (will increase sector writes);
- pppoe-client - implemented fastpath support;
- l2tp - implemented l2tp and lns fastpath/fasttrack support;
- queue - added bucket-size setting to queues (derived from max-limit);
- tile - fixed rare situation when some cores decide not to take part in packet processing till next reboot;
- tunnels - fixed performance slowdown on any other tunnel disable/enable;
- winbox - increased minimal required winbox version to 3.4;
- wireless - added new package "wireless-rep";
- wireless - improved 1-chain 802.11ac station compatibility with other vendor multi-chain APs;
- address-list - fixed crash in low memory situations;
- bonding - fixed crash when creating vlans on bonding interface;
- capsman - added 802.11g/n band;
- capsman - fixed capsman extension channel names;
- certificate - revoked certificates not showing as (R)evoked;
- certificate - allow manual crl url addition;
- chr - added support for VLAN on Hyper-V;
- chr - fixed Hyper-V booting from SCSI;
- chr - fixed Hyper-V on windows 8/10 reboot loop;
- chr - fixed bridge firewall;
- chr - fixed kernel crash when virtual ethernet was not connected to anything in Hyper-V;
- chr - implemented automatic storage increase on disk image size increase;
- chr - implemented kernel crash saving to autosupout.rif (will utilize additional 24Mb of RAM);
- chr - make shutdown request from hyper-v work (might fix other hypervisor as well);
- chr - no more installation on first boot;
- chr - try to renew expired license once a hour instead of 100h;
- cloud - don't write minor status changes to storage;
- console - fixed print follow in "/ip dns cache" menu;
- console - show RouterOS Version in /interface wireless scan;
- console - sort completions/hints in natural order;
- console - update copyright notice;
- defconf - fixed default configuration for SXT LTE;
- dhcpv6-client - fixed wrong error message;
- dhcpv6-client - fix ia expiration and lifetime validation;
- dhcpv6-server - acquire binding on renew if it does not exist;
- dude - (changes discussed here: http://forum.mikrotik.com/viewtopic.php?f=8&t=104395);
- dude - fixed dude login logging, no more shows as winbox login;
- email - fixed send cmd server addr override;
- ethernet - add option to see S-GPON-ONU module, GPON side SN in "/int eth mon sfp#";
- ethernet - do not allow to set self as master port;
- export - bonding did not show up in global export;
- export - exclude default values from export in "/interface l2tp-server server" menu;
- export - fixed export when ipv6 address was taken from pool;
- export - fixed rare situations when not whole config was exported;
- export - updated defaults for compact export;
- fastpath - fixed crash when packet arrives on disabled interface;
- fastpath - fixed show rx-bits-per-second on all VLAN interfaces;
- fastpath - improved vlan fastpath;
- fasttrack - fixed timer updating in connections table for fasttrack connections;
- fetch - decrease connection idle timeout;
- firewall - added experimental "action=route" in mangle prerouting - that forces packets to specific gateway by ignoring routing decisions (CLI oly);
- health - always report fan speed (even if it is 0);
- health - swap fan2 and fan3 on CCR1072;
- hotspot - clean-up all dead entries at once;
- hotspot - fixed possible deadlock;
- hotspot - improved html page resistance against attacks;
- hotspot - make video tag work properly on hotspot login.html page
- ip - rename max-arp-entries to less confusing max-neighbor-entries;
- ippool6 - fixed potential crash;
- ipsec - always re-key ph1 because it was possible that ph1 without DPD would expire;
- ipsec - better flush on proposal change;
- ipsec - fixed crash on policy update;
- ipsec - fixed fast ph2 SA addition;
- ipsec - fixed larval SA refresh for display;
- ipsec - fixed multiple consecutive dynamic policy flush;
- l2tp & pppoe - fixed user traffic accounting when fastpath was used;
- l2tp - introduced per tunnel allow-fast-path option;
- l2tp - added support for Hidden AVP, it is needed for proxy authentication;
- l2tp - added support for max-sessions;
- l2tp - added support for proxy authentication when receiving forwarded PPPoE sessions;
- l2tp - fixed small memory leak on reconnects;
- lcd - fixed branding packet logo drawing on startup;
- led - fixed crash on assigned interface removal;
- led - turn on fault led on CCR1072 if CPU too hot;
- leds - fixed AP-CAP led blinking after successful association to CAPsMAN;
- lte - added ipv6 support for SXT LTE;
- lte - changed AT command processing;
- lte - changed AT parsing because supported Huawei modems use unsolicited events instead of polling;
- lte - fixed bandlux modem dialing;
- lte - fixed crash on early initialization;
- lte - improve situation when SXT modem never finds operator;
- lte - replaced signal-strength with rssi in info command;
- lte - support Alt38XX modem;
- lte - support for zte mf820s2;
- lte - supported modems now use unsolicited events for network monitoring;
- lte - use timer for modem info;
- map lite - added hardware WPS button support;
- mpls - do not reset VPLS on TE tunnel re-optimize;
- ntp - fixed ntp client hangs in reached state;
- ospf - fixed crash when getting neighbor router-id in NBMA area;
- ppp - fixed ppp interface reconnect when uPnP was used;
- ppp - close connection if peer wants to re-authenticate;
- ppp - fixed memory leak high number of pppoe clients to the same server;
- ppp - fixed ppp crash if lcp packets were lost and authentication got delayed;
- ppp - fixed some clients can not connect due to LCP restart;
- pppoe - added rfc4679 support;
- pppoe - fixed crash when removing pppoe service;
- pppoe-server - added pado-delay option;
- profiler - classify certificate signing;
- proxy - fixed ftp request url decode;
- queue - improve "/queue interface" menu;
- quickset - fixed invalid date adjusted the signal threshold for the signal chart and refresh rate;
- quickset - fixed situations when hidden password was passed as ******* from winbox nd webfig;
- radius - warn radius client if incorrect secret is being used;
- rb3011 - fixed sfp compatibility with CCR when using direct attached cables;
- rb3011 - fixed time keeping;
- rb3011 - make ether6-ether10 work if SFP module is present on bootup;
- romon-ssh - fixed active addresses for romon user;
- route - do not show duplicate gateway on connected route;
- route - fixed filter by routing table;
- routing - fixed rare kernel failure on different dynamic routing configurations;
- routing - fixed routing-marks were not erased from memory when they are not being used;
- services - do not show ssh entry under ip services if security package is disabled;
- snmp - don't group oids for bulk get with maxreps > 1 ;
- snmp - fixed cpu load reporting to 1min average and change oid to 1.3.6.1.4.1.2021.11.10.0;
- snmp - fixed dhcpv4 lease hwaddr format according to mib;
- snmp - fixed getbulk result ordering with multiple request OIDs;
- ssh - simplify login process;
- ssl - optimized certificate update;
- system - log time changes;
- tile - corrected max-l2mtu;
- tile - fixed fastpath related memory leak;
- tile - fixed performance regression on switch chip (introduced in 6.33rc18);
- tile-crypto - fixed minor memory leak;
- tool fetch - fixed https cleanup on user stop while handshaking;
- trafficgen - fixed console arguments;
- trafficgen - fixed crash when unexpected stream reappears;
- trafflow - fixed potential deadlock;
- ups - fixed entering hibernate mode when below battery capacity limit;
- users - added separate RoMoN policy;
- webfig - fixed firewall rule sorting did not work in other chains except all;
- webfig - show single item groups as optional values;
- webfig - sort numeric columns numerically even if they contain some text;
- winbox - added "pw-type" to "/interface vpls bgp-vpls" menu;
- winbox - added "use-control-word" and "pw-mtu" to "/interface vpls cisco-bgp-vpls" menu;
- winbox - added /interface wireless setup-repeater;
- winbox - added all the rates settings to the capsman;
- winbox - added flip-screen option to lcd settings;
- winbox - added init-delay option to routerboard settings;
- winbox - added ipv6 firewall missing log option;
- winbox - added missing eap-ttls-mschamv2 method to wireless security profile;
- winbox - added mtu=auto support to eoipv6 tunnel;
- winbox - added sfp-mac for GPON interfaces;
- winbox - added support for new settings from wireless-rep package;
- winbox - added support for route action in mangle rules;
- winbox - allow to set additional-network-modes;
- winbox - allow to set multiple dh-groups;
- winbox - disable autostart for wireless scan,snooper,align etc. on open;
- winbox - do not show "enable-jumper-reset" setting on devices without serial port;
- winbox - do not show real-tx-power column in current-tx-power by default;
- winbox - fixed unset options in /routing ospf interface menu;
- winbox - hotspot default-trial user shows profile as "unknown" in Winbox;
- winbox - improved winbox connection loss detection, fixes winbox safe mode;
- winbox - limit ospf key to 16 symbols;
- winbox - make additional-network-mode optional for lte interface;
- winbox - make build with latest lte changes;
- winbox - make mrru disabled and set mtu+mru to auto by default on new servers;
- winbox - show "usb-power-reset" option on all boards that have it;
- wireless - fixed crash on nstreme-dual interface stats update;
- wireless-rep - added 802.11g/n only band;
- wireless-rep - added STEP feature for the scan-list;
- wireless-rep - added WPS client support;
- wireless-rep - added support for saving wireless scan results to file;
- wireless-rep - added support for wireless background scan for 802.11 protocol;
- wireless-rep - added support for wireless repeater mode for 802.11 protocol;
- wireless-rep - added support for wireless scan rounds setting;
- wireless-rep - adjust roaming scan times;
- wireless-rep - allow to connect to AP after scan;
- wireless-rep - do not allow empty ssid for AP modes;
- wireless-rep - fixed crash on non-HT clients;
- wireless-rep - fixed latency issues with Intel wireless clients;
- wireless-rep - fixed nv2 protocol;
- wireless-rep - fixed qos frame-priority when nv2 protocol used in station-wds mode;
- wireless-rep - fixed signal leds;
- wireless-rep - fixed speed issue when connected with Intel 802.11ac;
- wireless-rep - initial support for station roaming for station mode in 802.11 protocol;
- wireless-rep - request interface name for setup-repeater;
- wireless-rep - use full identity where possible;
- wireless-rep,capsman - added more configuration settings;
- wireless-rep,capsman - added rate config support.
Полезные материалы по MikroTik
Углубленный курс "Администрирование сетевых устройств MikroTik" Онлайн-курс по MikroTik с дипломом государственного образца РФ. Много лабораторных работ с проверкой официальным тренером MikroTik. С нуля и до уровня MTCNA.
На Telegram-канале Mikrotik сэнсей можно получить доступ к закрытой информации от официального тренера MikroTik. Подписывайтесь